Product Description
Accessories
1) Cage mesh, cage frame,
2) Drinking system: fully automatic, tap or big water tank connected drinking system, nipple drinker, water pipe, "T" connector, "I" connector, "L" connector, water tank, water pressure regulator, filter
3) Feeding system: feeder trough, feeder connector, feeder cover, Worker to put the food into the feeder.
Nipple drinkers:stainless steel nipple drinkers, The professional poultry water pipe is made of good PVC material ,Length 4m/pcs.,guaranty is more than 15 years, without leakage and long service life.
The silver white feeding trough length is 3.84m/pcs, made of concentrate PVC,Loading capacity is more than 60kg/pcs
We can supply A,H type layer chicken equipment chicken shed the follow system for chicken farm:
1. Automatic pan feeding system
2. Nipple drinking system
4. Ventilation system
5. Cooling pad system
6. Heating system
7. Environment control system and auto collected egg system
Brief Introduction of Poultry House
Main Structure
(Steel tube truss system)we adopt hot-dip galvanizing C section or steel tube truss beam to reduce self-weight of design load and dosage of the steel. At the same time, hot-dip galvanized can widely improve anti-corrosion of the steel. (The construction cycle of the steel structure work is short, which reduces the cost of the project effectively. The steel structure has strong shock resistance and can improve the comprehensive anti-seismic property of the whole house).
Substructure(Cold-formed thin-walled steel)
Roof purlin uses the hot-dip galvanized Z or C section. The way to continuous lap makes the steel frame as whole. Roof purlin uses the hot-dip galvanized C section steel. All components adopt bolted connection, no welding, which makes the structure overall appearance smooth.
Protecting system
In order to satisfy the protecting material for 20 years, the outside roof is 0.5 mm aluminum zinc color steel plate. To prevent dewing phenomenon, 50 mm aluminum foil glass wool is laid at the bottom of the roof plate (can be customized according to the climatic conditions). To prevent sagging of the fiber wool, the wire mesh is added, which effectively improve the utilization rate of the glass wool insulation and moisture proof. To add ceiling panels below steel trusses and the ceiling panels laid horizontally is composite color plate, which not only improves the overall stability of steel trusses, but also plays a very good thermal insulation effect. The inside and outside walls laid horizontally is hot-dip galvanized color steel plate, which are all used self-tapping screw to connect into a whole, effectively increasing the lateral stability of steel columns. The indoor humidity is relatively large, so a layer of plastic film is added in order to prevent moisture from entering the fiber glass wool.
Basic rules of structure design
1. Design code for steel structure GB50017-2003;
2. Design Specification for Curved Thin-walled Steel Structure GB50018-2002.
Design parameters
1. Coefficient for importance of a structure is 0.95. The usage life is 25 years;
2. 3 security level;
3. Seismic fortification categories: C-class;
4. Earthquake-resistant level: the main structure is level four.
Structural design load
Uniformly distributed load standard values:KN/m2
1. YX-980 0.5mm outsider roof aluminum-zinc steel plate: 0.049KN/m2;
2. 16kg/m3 50mm heat-insulating fiber glass wool: 0.008 KN/m2;
3. Z or C roof purlin: 0.034 KN/m2;
4.Roof live load: 0.5 KN/m2.
Concentrated load:KN/m2(3mis a lifting point)
1. Waterline : 0.11 KN/m2;
2. Feed line : 0.22 KN/m2;
3. Motor(the end of waterline and feed line): 0.41 KN/m2;
4. Full load of hopper : 1 KN/m2;
5. Main feed line : 0.18 KN/m2;
6. Wind load : 0.6 KN/m2;
7. Snow load : 0.5 KN/m2.
Material
Load-bearing structural steel (steel column, steel beam) usually adopt Q235 and Q345. According to machinery performance and chemical composition, Steel should be Q235B which conforms to the requirement of current national standard high strength low alloy structural steel (GB/T1591-94) and (GB1591-88).
The ration of the steel tensile strength and yield strength measured value should not be less than 1.25, and there is obvious yield level. Elongation should be more than 20%, and has good weld ability and qualified impact toughness.
Material List for Prefab Steel Structure Poultry House |
Foundation |
Anchor bolts |
|
Canopy |
steel frame + steel sheet |
Column |
H section steel |
Roof cladding |
EPS sandwich panel |
Tubular pillar |
PU sandwich panel |
Lattice column |
Rockwool sandwich panel |
Cross column |
Corrugated steel sheet |
Box column |
Skylight panel |
Beam |
H section steel |
Ventilator |
Lattice beam |
Wall cladding |
EPS sandwich panel |
Pipe truss |
PU sandwich panel |
Space frame |
Rockwool sandwich panel |
Roof purlin |
C section steel |
Corrugated steel sheet |
Z section steel |
Mezzanine |
Decking floor |
Wall purlin |
C section steel |
Checkered steel plate |
Tie bar |
Steel pipes |
Insulation |
Fiber glass wool |
Roof bracing |
Angle steel |
Fasteners |
High strength bolts |
Steel pipes |
Common bolts |
Column bracing |
Angle steel |
Expansion bolts |
Steel pipes |
Accessories |
Flashing |
Pulling strap |
Steel round bar |
Trim |
Sleeves |
Steel pipes |
Gutter |
Knee bracing |
Angle steel |
Down pipe |
FAQ
1. What kind of company you are?
We are steel structure building Manufacturer located in Qingdao China, We were gaining good reputation among our customers for our professional, warm and thoughtful service. Because we know that a long terms business based on the quality control, price, packing, delivery time etc.
2. Does your company is a factory or trade company?
We are factory, so you will enjoy the best price and competitive price. Our factory covers an area of 150,000 square meters.
3. Whats the quality assurance you provided and how do you control quality ?
Established a procedure to check products at all stages of the manufacturing process - raw materials, in process materials, validated or tested materials, finished goods, etc.
4. Can you offer designing service?
Yes, we have more than 100 design engineers. We could design full solution drawings as per your requirements. They use software: Auto CAD,PKPM, MTS, 3D3S, Tarch, Tekla Structures(X steel)V12.0.etc.
5. Do you offer guiding installation on site overseas?
Yes, we can provide the service of installation, supervision and training by extra. We can send our professional technical engineer to supervise installation on site overseas. Besides, We also have our own abroad guiding installation team consisting of more than 30 people.
Welcome to send your inquiry on blank as below